کنترلر LED پیکسلی T1000S

نحوه استفاده:

http://trainbit.com/files/0128537884/T-1000S_manual.pdf

برنامهLedEdit2012:

http://Trainbit.com/files/2528537884/software_for_T1000S_SD_card_controller.zip

آموزش برنامه LedEdit2012

http://Trainbit.com/files/4228537884/LedEdit2012_operating_manual.pdf

The T1000S SD card LED controller makes controlling your LED displays easy. Compatible with wide range of

addressable LEDs and DMX signal communication protocol.

Runs at DC 7.5-24V using an onboard voltage regulator, or can be run off a single DC 5V source if you're running DC 5V

Strips

Each controller can drive up to 2048 pixels using 256 brightness levels per color (24 bit color)

Supports all the various rules-shape, special shape processing

Off-line use can support 16 programmes stored in the SD card

Using buttons on the controller, you can adjust the playback speed and choose the display program. Achieve to save the play list functions

Built-in lightning resistant and ESD protection circuit, ensures safety and reliability

Compatible with wide range of addressable LED chipsets

TM1803/TM1804/TM1809/TM1812/TM1825/TM1826/TM1829/TA9909/TA9912

UCS1903B/UCS1903N/UCS1909B/UCS1912B/UCS2903/UCS2909/UCS2912/UCS3903/UCS3912/UCS8903/UCS8904

LPD6803/LPD1886/LPD1882/LPD1889/LPD6812/LPD6813/LPD8806/LPD8809

SM16716/SM16726/SM16711

WS2811/WS2801/WS2803

LX1003/LX2003/LX2006

INK1003/INK1009

P9813/P9816/D705

GW6201/GW6202B/GW6203/GW6204/GW6205/GW6206/GW6230/GW6231/GW6240/GW6241

BS0815/BS0825/BS0901

TLS3001/TLS3008/TLS3100

MBI16021/QC1109/APA102/MY9201/1001

D7710/D7720

DM134/74HC595/MBI5026/ZQL9712/SC16722

NOTE：
1. When T-1000S controller less than 512 pixels the frame rate can reach 30fps. When T-1000S control more than 512 pixels the frame rate will slow down automatically.

2. T-1000S must use the new software LedEdit 2012.
Multiple T-1000S controllers can be cascaded  together and work synchronous
T-1000S one TTL(SPI) signal and one RS485 signal port output，can control 2048 pixels
When the chip for LED is single line chip just with data, then just need to be connected with DAT and GND of the controller. If the chip for LED is double line chip with DAT and CLK, then need to be connected with DAT, CLK, and GND of the controller
If you need to use RS485 signal you need to connect controller A with LED A (DMX+), controller B with LED B(DMX-)
When you need to built a new project the controller type for the software is：T-1000-IC model
Special parameters:
Memory card：
type：SD card（suggest using high-speed SD card）
Capacity：128MB-2GB
Store file：*.led
Physical parameters：
Working temperature ：-30℃-85℃
Working voltage：DC5V / DC7.5-24V
Working power：1W
Size：16cm x 9cm x 2cm
Weight：253g
Signal port：3pin connect port